P-51 Mustang Plan






A Closer Look at This Product
Tech Notes  




Additional Pictures:

Instruction Manuals: None

Stock Number








Our designs are equally at home at the local sport flying field or the winner’s circle at prestigious scale events such as Top Gun and the Scale Master’s; you can add as much detail as you like. Over the years, our designs have gained the enviable reputation for being among the most “flyable” giant scale models available. 

The basic structures use conventional “modeling” tools and materials such as balsa and plywood, and the techniques are straightforward; easily accomplished by anyone with previous model building experience. Most plans have separate instruction guides and building notes on the plans.

The P-51 Mustang plan set consists of four large sheets that clearly illustrate all structure as well as showing installation of flaps and retracts. The plan includes full-size templates for all the required parts allowing you to cut a complete “kit” before you start construction.



Scale: 1/4.6

Inches to the foot: 2.6" - 1'

Length: 83"

Weight: 28 - 36 lbs

Wing loading: 39 - 50 oz/sqft

Wing area: 1650 sq.in.

Wing span: 98"

Wing incidence at root: +2 1/2 degrees

Stab incidence: +1 degree

Dihedral: 5 1/4" under W14

Power: 62 - 85 cc gas

Washout at wing tip:  2 to 3 degrees built in with jig

Aileron throws: 3/4" up & 1/2" down

Elevator throws: 1" up & 1" down

Rudder throws: 1 1/2" to right & 1 1/2" to left

Flap degrees down: 40 - 50

Cowl length: 18 1/2"

Cowl height front: 7 1/2"

Cowl height rear: 11"

Cowl width front: 6"

Cowl width rear: 7"

Engine offset degrees: 1 right 1 down

CG location: 8 1/4" back from the leading edge of the wing at the fuselage




Ziroli cowls and or nose: yes

Ziroli canopy: yes

Ziroli plastic accessories: yes

Engine:62 - 85 cc gas

Spinner:  6"

Fuel tank: 32oz rectangle

Wing Tube: none

Control Horns: (3) 1/2", (2) 3/4"

Hinges: 26 LG flat hinges

Covering: 1 oz fiberglass cloth and epoxy resin

Retracts Main:  yes

Retracts Nose: no

Retracts Tail: yes

Main gear struts:  n/a

Tail gear strut: n/a

Air Kit:  yes

Wheels Main:  5 1/2" or 6"

Wheel Nose: n/a

Wheels Tail: 2"

Radio channels:  6 or more

Servos: Flaps (2) 150-200oz MGBB, Ailerons (2)90+oz BB, Elevators (2)90+oz BB, Rudder (1)120+oz BB, Gear (1)50oz, Throttles (1)50oz BB

MG-metal gear BB-ball bearing





Our plans show either Robart retracts or struts or fixed wire gear, also available are quality landing gear made for our planes by other manufacturers such as Sierra Giant Scale, Century Jet and others. Which ever gear you choose you should have it on hand when you start construction to make any changes needed for mounting or make adjustments and check fitting. The same holds for mounting of engines other than those shown on the plan. We recommend 1oz fiberglass cloth and ZAP Z-poxy finishing resin to cover our balsa sheeted designs and Stits covering and painting System or Solartex covering on designs with open structure. Epoxy paints give best resistance to gasoline and cracking. We now carry laser cut short wood kits for our plans that contain all the parts that you would other wise have to cut by hand from balsa and plywood, it does not include sheet or stick wood. There are many kit cutters such as Precision Cut Kits that make a very fine full wood kits that contains all the sheet, stick wood and laser cut parts to build the model from our plans and fiberglass fuse versions. We now have fiberglass fuselages available for some of our designs and we are adding to the list all the time. We carry many scale items (props, RED5vinyl graphic sets, exhaust, pilots, etc.) for our designs, check our Scale Items section.